Rm-materials-handling VARIABLE SPEED CONTROLS ControlMaster Plus Service Manual do Utilizador descarregar pdf (Página 32)

R&M Materials Handling, Inc.

4501 Gateway Boulevard

Springfield, Ohio 45502

P.: (937) 328-5100

FAX: (937) 325

5319

32/83

R&M Materials Handling, I

nc. reserves the right to alter or amend the above information without notice.

G4.7. Digital Input

S1 V4.7.1.1. State of digital input S1 0=OFF, 1=ON

S2 V4.7.1.2. State of digital input S2 0=OFF, 1=ON

DIA3 V4.7.1.3. State of digital input DIA3 0=OFF, 1=ON

DIA4 V4.7.1.4. State of digital input DIA4 0=OFF, 1=ON

DIA5 V4.7.1.5. State of digital input DIA5 0=OFF, 1=ON

OK V4.7.1.6. State of digital input OK 0=OFF, 1=ON

DID1 V4.7.1.7. State of digital input DID1 0=OFF, 1=ON

DID2 V4.7.1.8. State of digital input DID2 0=OFF, 1=ON

DID3 V4.7.1.9. State of digital input DID3 0=OFF, 1=ON

DID4 V4.7.1.10. State of digital input DID4 0=OFF, 1=ON

DID5 V4.7.1.11. State of digital input DID5 0=OFF, 1=ON

Basic Board V4.7.3. State of board A inputs

Corresponding X1 terminals

DIA3

DIA4

DIA5

0=OFF, 1=ON

Extension Board V4.7.4. State of board D inputs

Corresponding X1 terminals

DID1

DID2

DID3

DID4

DID5

0=OFF, 1=ON

G4.8. SSU

Overspd Lim 1 V4.8.1. Overspeed limit 1 level. Percent of Max Freq S2 0 – 140 %

Overspd Lim 2 V4.8.2. Overspeed limit 2 (ESR) value. Percent of Max Freq S2 0 – 140 %

G4.9. Service

Phase U Curr V4.9.1. Phase U current of inverter output A

Phase V Curr V4.9.2. Phase V current of inverter output A

Phase W Curr V4.9.3. Phase W current of inverter output A

Encoder Speed V4.9.4. Pulse frequency from pulse sensor. Both A and B channel must be in

use.

HeatSinkTempMax V4.9.5. Recorded heatsink temperature highest peak value during run.

°C

HeatSinkTempMin V4.9.6. Recorded heatsink temperature lowest peak value when power is

connected to drive.

°C

IGBT Temp Max V4.9.7. Recorded calculated IGBT temperature highest peak value.

°C

IGBT Temperature V4.9.8. Actual IGBT temperature

°C

SlipAdjustChange V4.9.9. Slip adjust difference compared to Slip adjust parameter. %

G4.9.10 Max Current.

Max Current G4.9.10.1. Recorded maximum current A

Max Current Freq G4.9.10.2. Frequency at recorded maximum current. Hz

Max Current Torq G4.9.10.3. Torque at recorded maximum current. %

G4.9.11 Encoder

V4.9.11.1 Not used.

V4.9.11.2 Not used.

V4.9.11.3 Not used.

V4.9.11.4 Not used.

V4.9.11.5 Not used.

Freq Ref V4.11. Frequency reference Hz

Speed Req V4.12. Not used.

Distance counter V4.13. Not used m

DC-Link Voltage V4.14. Actual value of measured DC-link voltage. V

Heat Sink Temp V4.15. Temperature of heat sink.

°C

MotorTemperature V4.16. Calculated motor temperature in percent of maximum %

Motor Power V4.17. Calculated actual power. % of nominal power of unit %

Motor Voltage V4.18. Calculated motor voltage V

Motor Torque V4.19. Calculated motor torque

+/- motor nominal torque, positive when motoring, negative when

generating.

Motor Current V4.20. Measured motor current A

Motor speed V4.21 Calculated motor speed Rpm

Output frequency V4.22 Output frequency to the motor Hz

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 82 83

Comentários a estes Manuais

Sem comentários

Rm-materials-handling VARIABLE SPEED CONTROLS ControlMaster Plus Service Manual do Utilizador Página 32

Comentários a estes Manuais