Rm-materials-handling ELECTRIC CHAIN HOISTS LoadMate Chain Hoist LM 10 S Manual do Utilizador descarregar pdf (Página 42)

LM10 STEPLESS I&M MANUAL/EN/11.30.2010

42/99

This document and the information contained herein, is the exclusive property of R&M Materials Handling, Inc., and represents a non-public, confidential and proprietary trade secret that

may not be reproduced, disclosed to third parties, altered or otherwise employed in any manner whatsoever without the express written consent of R&M Materials Handling, Inc.

G1.3 I/O Parameters

Code Name Min Max Unit Description

P1.3.1 ROA1 0 12 State of relay output ROA1 (See Chapter "Relay output")

0 = Not Used

1 = Fault

2 = External Brake Control

3 = Run, current is fed to the motor, default

4 = Drive is ready to operate

5 = Drive is NOT ready to operate

6 = Fan. DC-link voltage is above braking chopper operating value –70V. Relay

is closed minimum 300s.

7 = Emergency Stop, relay is activated in case of faults F1 Overcurrent, F2

Overvoltage, F3 Earth Fault. Relay is deactivated when the power is switched

off.

8 = Reverse Plugging. Direction request is different than direction of actual

frequency.

9 = At Speed. The Drive has reached the speed reference request.

10 = S2 Active. Motor actual speed direction is S2.

11 = Temp1. Relay is activated when temperature is 20ºC (68F) or below.

Relay is inactivated when temperature is 23ºC (73F) or above.

12 = Temp2. Relay is activated when temperature is 40ºC (104F) or above.

Relay is inactivated when temperature is 37ºC (98F) or below.

P1.3.2

Ain1 Minimum

Voltage

0.000 10.000 V Minimum value of analog input Ain1 for AU-control

P1.3.3

Ain1 Maximum

Voltage

0.000 10.000 V Maximum value of analog input Ain1 for AU-control

P1.3.4 Aout Function 0 5 0 = Not Used

1 = Motor Freq (100%*Normal Motor Frequency)

2 = Motor Curr (100%*Normal Motor Current)

3 = Motor Volt (100%*Normal Motor Voltage)

4 = DC-link Volt (1000V)

5 = MotorFreqABS (Absolute value of Motor Frequency)

P1.3.5 Aout Zero Current 0.00

Aout

Nom

Curr

P1.3.6

Aout Nominal

Current

Aout

Zero

Curr

100.00 mA

G1.4 Not used

Code Name Min Max Unit Description

P1.4.1 0 = Default value

1 = must not be used

2 = must not be used

P1.4.2 Not used

P1.4.3 Not used

P1.4.4 Not used

P1.4.5 Not used

G1.5 Expert

Code Name Min Max Unit Description

P1.5.1 Slowdown Mode 0 2 0 = Slow

1 = Fast, default

2 = Fast Power Up (See Chapter "Slowdown-limit operation")

P1.5.2 S-Curve 0.00 0.50 s

The start and end of the acceleration and end of deceleration ramp can be

smoothed with this parameter. Setting value 0.00-0.50 seconds for this

parameter produces an S-shaped acceleration/deceleration.

P1.5.3 Ramp Stretching 0.00 50.0 See Chapter "Ramp Stretching". Not used in hoisting

P1.5.4 Switching Frequency

Must not be changed from factory setting

P1.5.5 Brake Chopper 1, default

Must not be changed

1 2 ... 37 38 39 40 41 42 43 44 45 46 47 ... 98 99

Comentários a estes Manuais

Sem comentários

Rm-materials-handling ELECTRIC CHAIN HOISTS LoadMate Chain Hoist LM 10 S Manual do Utilizador Página 42

Comentários a estes Manuais

Manuais e produtos relacionados com Guincho Rm-materials-handling ELECTRIC CHAIN HOISTS LoadMate Chain Hoist LM 10 S